There are no products in your shopping cart yet.
DCC concepts
2 / 2
Loading...
6m grey decoder wire - DCC concepts
€ 3,39
6m grey decoder wire - DCC concepts
Suitable for DCC installations in N, HO/OO and O.
32 Gauge
0.5 mm thick.
More DCCconcepts products
6m orange decoder wire - DCC concepts
€ 3,39
6m orange decoder wire - DCC concepts
Suitable for DCC installations in N, HO/OO and O.
32 Gauge
0.5 mm thick.
More DCCconcepts products
6m pink decoder wire - DCC concepts
€ 3,39
6m pink decoder wire - DCC concepts
Suitable for DCC installations in N, HO/OO and O.
32 Gauge
0.5 mm thick.
More DCCconcepts products
6m purple decoder wire - DCC concepts
€ 3,39
6m purple decoder wire - DCC concepts
Suitable for DCC installations in N, HO/OO and O.
32 Gauge
0.5 mm thick.
More DCCconcepts products
6m white decoder wire - DCC concepts
€ 3,39
6m white decoder wire - DCC concepts
Suitable for DCC installations in N, HO/OO and O.
32 Gauge
0.5 mm thick.
More DCCconcepts products
6m yellow decoder wire - DCC concepts
€ 3,39
6m yellow decoder wire - DCC concepts
Suitable for DCC installations in N, HO/OO and O.
32 Gauge
0.5 mm thick.
More DCCconcepts products
1m black power bus wire 1.5mm - DCC concepts
€ 1,09
1 m red power bus wire 1.5mm2
1 m fine stranded power bus wire.
Colour: red.
The perfect bus wire for medium sized N, HO/OO and O gauge layouts.
1,5 mm2 (15 gauge AWG).
More DCCconcepts products
1 m black power bus wire 2.5mm - DCC concepts
€ 2,25
1 m black power bus wire 2.5mm2
1 m fine stranded power bus wire.
Colour: black.
The perfect bus wire for medium sized N, HO/OO and O gauge layouts.
2,5 mm2 (13 gauge AWG).
More DCCconcepts products
25 m black power bus wire 2.5mm - DCC concepts
€ 27,50
25 m black power bus wire 2.5mm2
1 rol with 25m fine stranded power bus wire.
Colour: black.
The perfect bus wire for medium sized N, HO/OO and O gauge layouts.
2,5 mm2 \(13 gauge AWG).
More DCCconcepts products
Weathering powders - shades of grey - DCC concepts
€ 13,75
This set contains four shades of grey to weather your layout and scenic areas.
More DCCconcepts products
36 pack heat schrink clear - DCC concepts
€ 4,49
36 pack heat schrink clear - DCC concepts
Length: approx. 55 mm.
Diameter: approx. 2 mm.
More DCCconcepts products
36 pack heat schrink red - DCC concepts
€ 4,49
36 pack heat schrink red - DCC concepts
Length: approx. 55 mm.
Diameter: approx. 2 mm.
More DCCconcepts products
36 pack heat schrink assorted colours - DCC concepts
€ 4,49
36 pack heat schrink assorted colours - DCC concepts
Length: approx. 55 mm.
Diameter: approx. 2 mm.
More DCCconcepts products
Weathering powders - locos and wagons - DCC concepts
€ 13,75
This set contains four colours of weathering powder to weather your locos and wagons.
More DCCconcepts products
1m red power bus wire 2.5mm - DCC concepts
€ 1,09
1 m red power bus wire 1.5mm2
1 m fine stranded power bus wire.
Colour: red.
The perfect bus wire for medium sized N, HO/OO and O gauge layouts.
1,5 mm2 (15 gauge AWG).
More DCCconcepts products
1 m red power bus wire 2.5mm - DCC concepts
€ 2,25
1 m red power bus wire 2.5mm2
1 m fine stranded power bus wire.
Colour: red.
The perfect bus wire for medium sized N, HO/OO and O gauge layouts.
2,5 mm2 (13 gauge AWG).
More DCCconcepts products
Powerbase Expansion Pack HO/OO - DCC concepts
€ 15,75
Powerbase Expansion Pack HO/OO - DCC concepts
For OO/HO and larger scales. Contains approx. 5 Metres of PowerBase Centipede Plates.
Powerbase Expansion Pack N - DCC concepts
€ 19,25
Powerbase Expansion Pack N - DCC concepts
For N or TT scale & Narrow Gauge. Contains approx. 2.5 Metres of PowerBase Centipede Plates. Usable with any track formation, set track, flex track and any track brand. Usable with all track radii.
Powerbase Starter Kit HO/OO - DCC concepts
€ 23,95
Powerbase Starter Kit HO/OO - DCC concepts
For OO/HO and larger scales. Contains approx. 2.5 Metres of PowerBase Centipede Plates, 6 magnets and 6+ housings, plus pan head screws to assist magnet mounting. (enough for 2-3 4mm scale locomotives).
Powerbase Start Kit N - DCC concepts
€ 23,95
Powerbase Start Kit N - DCC concepts
For N or TT scale & Narrow Gauge. Contains approx. 2.5 Metres of PowerBase Centipede Plates. Usable with any track formation, set track, flex track and any track brand. Usable with all track radii.
Magnets and parts - Powerbase - DCC concepts
€ 17,95
12 magnets with pouches and about 30 screws to assist magnet mounting.
More DCC concepts products
Power base mini magnet - 30 pack - DCC concepts
€ 17,25
a selection of 30 small magnets.
More DCC concepts products
3 pack end of train lamps - DCC concepts
€ 31,15
End of Train Lamp (with All Electronics) (3 Pack)
3x Beautifully crafted scale sized modern EOT lamp complete with 3 full sets of onboard electronics for lamp flash, featuring the ability to automatically turn on/turn off and ready for accessory decoder connection too. Easy mounting with a simple rear pin. Super-fine 0.12mm wire for an almost invisible connection (see online manual for instructions)..
Working loco lamps LMS/BR - red light - DCC concepts (6 Pack)
€ 22,95
Working loco lamps LMS/BR - red light - DCC concepts (6 Pack)
6 x accurate 4mm scale working loco lamps, LMS / BR type, red light.
6 working loco lamps LMS/BR scale O - red light - DCC concepts
€ 22,95
6 working loco lamps LMS/BR scale O - red light - DCC concepts
6 x accurate 4mm scale working loco lamps, LMS/BR type, red light.
6 working guards van lamps LMS/BR scale O - white and red light - DCC concepts
€ 29,85
6 working guards van lamps LMS/BR scale O - white and red light - DCC concepts
6 x accurate 4mm scale working guards van lamps, LMS/BR type, white and red light.
The lights go on the sides of a guards/brake van with the white light forwards. This is to tell the driver that the guards van is still attached to the, sometimes partly, braked train. A guards/brake van also carries a red light in the center. The three red lights tell signalmen and linesmen that the whole train has passed them.
6 working loco lamps LMS/BR scale O - white light - DCC concepts
€ 22,95
6 working loco lamps LMS/BR scale O - white light - DCC concepts
6 x accurate 4mm scale working loco lamps, LMS/BR type, white light.
Pre-Etched Sleepers 1.6mm (4mm scale) 3 way points - DCC concepts
€ 15,50
4mm scale UK prototype Pointwork sleepering, pre-etched. This fret contains enough correct length sleepers to allow a 3 way point to be constructed. Tie Bars included. Sleepers are 1.6mm thick for direct soldered construction. Designed for 4mm scale / 16,5mm gauge and OO-SF.
template for asymmetric 3 way point (pdf)
More DCCconcepts products
Pre-Etched Sleepers 1.6mm (4mm scale) diamond crossing. - DCC concepts
€ 15,50
4mm scale UK prototype Pointwork sleepering, pre-etched. This fret contains enough correct length sleepers to allow a selection of Diamonds to be constructed. Tie Bars included. Sleepers are 1.6mm thick for direct soldered construction. Designed for 4mm scale / 16,5mm gauge and OO-SF.
The thickness of these sleepers is 1.6mm and they vary in length.
template for 5 and 6 crossing (pdf)
template for 7 and 8 crossing (pdf)
More DCCconcepts products
Pre-Etched Sleepers 1.6mm (4mm scale) double slip - DCC concepts
€ 15,50
4mm scale UK prototype Pointwork sleepering, pre-etched. This fret contains enough correct length sleepers to allow a selection of slips to be constructed. Tie Bars included. Sleepers are 1.6mm thick for direct soldered construction. Designed for 4mm scale / 16,5mm gauge and OO-SF.
template for double slip 7 and 8 (pdf)
More DCCconcepts products
Pre-Etched Sleepers 1.6mm (4mm scale) B9 to A5 Points. - DCC concepts
€ 15,50
4mm scale UK prototype Pointwork sleepering, pre-etched. This fret contains enough correct length sleepers to allow any point between B9 and B6 and A5 to be constructed. Tie Bars included. Sleepers are 1.6mm thick for direct soldered construction. Designed for 4mm scale / 16,5mm gauge and OO-SF.
The thickness of these sleepers is 1.6mm and they vary in length.
template for A5 turnout (pdf)
template for B6 turnout (pdf)
template for B7 turnout (pdf)
template for B8 turnout (pdf)
template for B9 turnout (pdf)
More DCCconcepts products
Pre-Etched Sleepers 1.6mm (4mm scale) single outside slip - DCC concepts
€ 15,50
4mm scale UK prototype Pointwork sleepering, pre-etched. This fret contains enough correct length sleepers to allow a selection of slips to be constructed. Tie Bars included. Sleepers are 1.6mm thick for direct soldered construction. Designed for 4mm scale / 16,5mm gauge and OO-SF.
template for outside slip (pdf)
More DCCconcepts products
ESP wireless DCC Receiver - DCC concepts
€ 64,95
€ 48,71
ESP wireless DCC Receiver - DCC concepts
DCC-ESPR.1 is both an ESP® receiver and a 1.5Amp DCC system power bus generator as well as being a very clever “sniffer” device!
DCC-ESPR.1 can be powered by a DCC track bus or with any regulated DC power source or battery able to deliver from 12 to 20 volts.
It has just two pairs of terminals, a power switch and a pairing switch. Connect it to the track bus and it will synchronise mimic panels with all of your accessory operations.
Connect it to the sniffer port of your screen based system and it will update the display.
DCC-ESPR.1 can even be used as the entire basis for an independent DCC power bus, so it really is versatile – and simplicity itself!
DCC-ESPR.1 requires no “programming” and is already provided with a unique address at the time of manufacture. Of course, no two receivers will ever have the same address, so conflicts are 100% impossible!
Unlike Wi-Fi based systems, DCCconcepts ESP® has no limits on the quantity of linked transmitters and there is no need for routers, passwords or computers when using ESP®.
DCC-ESPR.1 has power-off memory and is also protected against wrong connections.
More DCC concepts products
DCC-ESPR.1 is both an ESP® receiver and a 1.5Amp DCC system power bus generator as well as being a very clever “sniffer” device!
DCC-ESPR.1 can be powered by a DCC track bus or with any regulated DC power source or battery able to deliver from 12 to 20 volts.
It has just two pairs of terminals, a power switch and a pairing switch. Connect it to the track bus and it will synchronise mimic panels with all of your accessory operations.
Connect it to the sniffer port of your screen based system and it will update the display.
DCC-ESPR.1 can even be used as the entire basis for an independent DCC power bus, so it really is versatile – and simplicity itself!
DCC-ESPR.1 requires no “programming” and is already provided with a unique address at the time of manufacture. Of course, no two receivers will ever have the same address, so conflicts are 100% impossible!
Unlike Wi-Fi based systems, DCCconcepts ESP® has no limits on the quantity of linked transmitters and there is no need for routers, passwords or computers when using ESP®.
DCC-ESPR.1 has power-off memory and is also protected against wrong connections.
More DCC concepts products
ESP 3-output DCC transmitter - DCC concepts
€ 51,95
€ 38,96
ESP 3-output DCC transmitter - DCC concepts
Very easy to use, this unit is the heart of ESP®.
DCC-ESPS.3 can be powered by a DCC track bus or with any regulated DC power source or battery able to deliver from 12 to 20 volts.
DCC-ESPS.3 has three inputs that can be connected to any form of detection or switch and three independent wireless outputs, each with its own DCC address.
The ESP® address range is from 1 to 2044.
To complete your wire-free installation, the DCC-ESPS.3 is paired with the DCC-ESPR.1 receiver which receives the commands and delivers them to your DCC system or control panel, either as a direct DCC command or as a “sniffer” device, so your screen-based DCC system can also receive feedback.
DCC-ESPS.3 can pair with multiple receivers.
Unlike Wi-Fi based systems, ESP® has no limits on the quantity of input channels and there is zero possibility of interference.
ESP® has full power-off memory and is also protected against wrong connections.
More DCC concepts products
Very easy to use, this unit is the heart of ESP®.
DCC-ESPS.3 can be powered by a DCC track bus or with any regulated DC power source or battery able to deliver from 12 to 20 volts.
DCC-ESPS.3 has three inputs that can be connected to any form of detection or switch and three independent wireless outputs, each with its own DCC address.
The ESP® address range is from 1 to 2044.
To complete your wire-free installation, the DCC-ESPS.3 is paired with the DCC-ESPR.1 receiver which receives the commands and delivers them to your DCC system or control panel, either as a direct DCC command or as a “sniffer” device, so your screen-based DCC system can also receive feedback.
DCC-ESPS.3 can pair with multiple receivers.
Unlike Wi-Fi based systems, ESP® has no limits on the quantity of input channels and there is zero possibility of interference.
ESP® has full power-off memory and is also protected against wrong connections.
More DCC concepts products
33m Kapton tape 5mm - DCC concepts
€ 11,45
33m Kapton tape 5mm - DCC concepts
Kapton is extremely thin but also very hard, and makes the perfect insulation tape for installations needing good insulation without bulk.
More DCCconcepts products
Intelligent inductive detector - Legacy Models
€ 23,70
Intelligent inductive detector - Legacy Models
The detector works on all layouts powered with every DCC brand or scale and every computer control IO input that can sense a high/low detection.
The detector will detect anything that alters the electrical state in a section. Examples are powered items such as Locomotives, illuminated coaches or rolling stock with resistive wheelsets. Even just a single tail lamp or a lamp in a Guards van or Caboose.
It is simple to install: It needs no soldering or complex set-up. It can be added later or at the time of layout creation. Just create a gap in one rail covering the area you wish to detect and pass the dropper wire which goes from the track power bus to that rail through the hole in the LM-iD coil. No other set-up or fiddling to do. It is that simple.
LM-iD is very easy to connect: every output uses screw terminals and it is possible to easily add an external panel LED and directly connect to and operate both low voltage logic-level things and higher current items such as relays.
One-year warranty.
3 pack - Intelligent inductive detector - Legacy Models
€ 68,60
3 pack - Intelligent inductive detector - Legacy Models
The detector works on all layouts powered with every DCC brand or scale and every computer control IO input that can sense a high/low detection.
The detector will detect anything that alters the electrical state in a section. Examples are powered items such as Locomotives, illuminated coaches or rolling stock with resistive wheelsets. Even just a single tail lamp or a lamp in a Guards van or Caboose.
It is simple to install: It needs no soldering or complex set-up. It can be added later or at the time of layout creation. Just create a gap in one rail covering the area you wish to detect and pass the dropper wire which goes from the track power bus to that rail through the hole in the LM-iD coil. No other set-up or fiddling to do. It is that simple.
LM-iD is very easy to connect: every output uses screw terminals and it is possible to easily add an external panel LED and directly connect to and operate both low voltage logic-level things and higher current items such as relays.
One-year warranty.
4 baseboard alignment dowels with powerpoint- DCC concepts
€ 24,95
4 baseboard alignment dowels with powerpoint- DCC concepts
These dowels are fitted with power bus conntion.
2 pairs of precision baseboard alignment dowels. Easy to install for accurate joining of baseboards.
Tools needed are: a pilot drill and a 13mm and 19mm spade bit.
2 pairs is enough to make two joints (Joins three baseboards together).
Gas street/platform lamps - black - 4mm scale - DCC concepts
€ 37,70
Gas street/platform lamps - black - 4mm scale - DCC concepts
Pack Contents
3x 4mm scale wall lamps with 200mm connection wires
3x Resistor boards – suitable for connection to regulated DC power 6-12V
Installation Advice
Drill the mounting hole using a 2mm drill. Carefully thread the fine wires into the hole, then insert the lamp mounting tube.
The longer of the 2 wires is the + lead. Connect your power supply to the resistor board and then try the lamp with each of the resistor values to select your preferred light level.
Alternatively, if a different level is wanted, you may also use any other value 1/4 watt resistor as long as it is larger than 1k Ohms.
Connect several lamps (up to 6) to one resistor board if you wish.
Power supply
Any regulated DC power supply between 6 and 15 volts will be suitable. (To save you any additional cost, you may find one in your bottom drawer, for example an unused mobile phone charger or any similar power supply).
Pack Contents
3x 4mm scale wall lamps with 200mm connection wires
3x Resistor boards – suitable for connection to regulated DC power 6-12V
Installation Advice
Drill the mounting hole using a 2mm drill. Carefully thread the fine wires into the hole, then insert the lamp mounting tube.
The longer of the 2 wires is the + lead. Connect your power supply to the resistor board and then try the lamp with each of the resistor values to select your preferred light level.
Alternatively, if a different level is wanted, you may also use any other value 1/4 watt resistor as long as it is larger than 1k Ohms.
Connect several lamps (up to 6) to one resistor board if you wish.
Power supply
Any regulated DC power supply between 6 and 15 volts will be suitable. (To save you any additional cost, you may find one in your bottom drawer, for example an unused mobile phone charger or any similar power supply).
Gas Wall lamps - black - 4mm scale - DCC concepts
€ 25,25
Gas Wall lamps - black - 4mm scale - DCC concepts
Pack Contents
2x 4mm scale wall lamps with 200mm connection wires
2x Resistor boards – suitable for connection to regulated DC power 6-12V
Installation Advice
Using a very small drill, drill the building wall to allow insertion of the fine wires. Use glue to fix the lamp to the building.
The longer of the 2 wires is the + lead. Connect your power supply to the resistor board and then try the lamp with each of the resistor values to select your preferred light level.
Alternatively, if a different level is wanted, you may also use any other value 1/4 watt resistor as long as it is larger than 1k Ohms.
Connect several lamps (up to 6) to one resistor board if you wish.
Power supply
Any regulated DC power supply between 6 and 15 volts will be suitable. (To save you any additional cost, you may find one in your bottom drawer, for example an unused mobile phone charger or any similar power supply).
Pack Contents
2x 4mm scale wall lamps with 200mm connection wires
2x Resistor boards – suitable for connection to regulated DC power 6-12V
Installation Advice
Using a very small drill, drill the building wall to allow insertion of the fine wires. Use glue to fix the lamp to the building.
The longer of the 2 wires is the + lead. Connect your power supply to the resistor board and then try the lamp with each of the resistor values to select your preferred light level.
Alternatively, if a different level is wanted, you may also use any other value 1/4 watt resistor as long as it is larger than 1k Ohms.
Connect several lamps (up to 6) to one resistor board if you wish.
Power supply
Any regulated DC power supply between 6 and 15 volts will be suitable. (To save you any additional cost, you may find one in your bottom drawer, for example an unused mobile phone charger or any similar power supply).
Swan-Neck street/platform lamps - black - 4mm scale - DCC concepts
€ 37,70
Swan-Neck street/platform lamps - black - 4mm scale - DCC concepts
Pack Contents
6x 4mm scale street/platform lamps with 200mm connection wires
2x 4mm scale wall lamps with 200mm connection wires
8x Resistor boards – suitable for connection to regulated DC power 6-12V
Installation Advice
Drill the mounting hole using a 2mm drill. Carefully thread the fine wires into the hole, then insert the lamp mounting tube.
The longer of the 2 wires is the + lead. Connect your power supply to the resistor board and then try the lamp with each of the resistor values to select your preferred light level.
Alternatively, if a different level is wanted, you may also use any other value 1/4 watt resistor as long as it is larger than 1k Ohms.
Connect several lamps (up to 6) to one resistor board if you wish.
Power supply
Any regulated DC power supply between 6 and 15 volts will be suitable. (To save you any additional cost, you may find one in your bottom drawer, for example an unused mobile phone charger or any similar power supply).
Pack Contents
6x 4mm scale street/platform lamps with 200mm connection wires
2x 4mm scale wall lamps with 200mm connection wires
8x Resistor boards – suitable for connection to regulated DC power 6-12V
Installation Advice
Drill the mounting hole using a 2mm drill. Carefully thread the fine wires into the hole, then insert the lamp mounting tube.
The longer of the 2 wires is the + lead. Connect your power supply to the resistor board and then try the lamp with each of the resistor values to select your preferred light level.
Alternatively, if a different level is wanted, you may also use any other value 1/4 watt resistor as long as it is larger than 1k Ohms.
Connect several lamps (up to 6) to one resistor board if you wish.
Power supply
Any regulated DC power supply between 6 and 15 volts will be suitable. (To save you any additional cost, you may find one in your bottom drawer, for example an unused mobile phone charger or any similar power supply).
Swan-Neck Wall lamps - black - 4mm scale - DCC concepts
€ 25,25
Swan-Neck Wall lamps - black - 4mm scale - DCC concepts
Pack Contents
2x 4mm scale wall lamps with 200mm connection wires
2x Resistor boards – suitable for connection to regulated DC power 6-12V
Installation Advice
Using a very small drill, drill the building wall to allow insertion of the fine wires. Use glue to fix the lamp to the building.
The longer of the 2 wires is the + lead. Connect your power supply to the resistor board and then try the lamp with each of the resistor values to select your preferred light level.
Alternatively, if a different level is wanted, you may also use any other value 1/4 watt resistor as long as it is larger than 1k Ohms.
Connect several lamps (up to 6) to one resistor board if you wish.
Power supply
Any regulated DC power supply between 6 and 15 volts will be suitable. (To save you any additional cost, you may find one in your bottom drawer, for example an unused mobile phone charger or any similar power supply).
Pack Contents
2x 4mm scale wall lamps with 200mm connection wires
2x Resistor boards – suitable for connection to regulated DC power 6-12V
Installation Advice
Using a very small drill, drill the building wall to allow insertion of the fine wires. Use glue to fix the lamp to the building.
The longer of the 2 wires is the + lead. Connect your power supply to the resistor board and then try the lamp with each of the resistor values to select your preferred light level.
Alternatively, if a different level is wanted, you may also use any other value 1/4 watt resistor as long as it is larger than 1k Ohms.
Connect several lamps (up to 6) to one resistor board if you wish.
Power supply
Any regulated DC power supply between 6 and 15 volts will be suitable. (To save you any additional cost, you may find one in your bottom drawer, for example an unused mobile phone charger or any similar power supply).
MPD loco storage and servicing cradle - 460mm - DCC concepts
€ 74,95
MPD loco storage and servicing cradle - 460mm - DCC concepts
Drive on/off loco storage that also functions as a service cradle.
The MPD loco storage is available in 3 lengths: 360, 460 and 560 mm.
More DCC concepts products
Drive on/off loco storage that also functions as a service cradle.
The MPD loco storage is available in 3 lengths: 360, 460 and 560 mm.
More DCC concepts products
MPD loco storage and servicing cradle - 560mm - DCC concepts
€ 87,45
Locomotief opbergdoos - 560mm - DCC concepts
Deze opbergdoos voor locomotieven heeft de mogelijkheid om locomotieven rechtstreeks uit de doos te laten rijden.
Tijdens transport zijn de locomotieven beschermd door de stevige doos.
De doos is tevens te gebruiken om onderhoud aan een locomotief te doen.
De locomotief opbergdoos is beschikbaar in 3 lengten: 360, 460 en 560mm.
Meer producten van DCC concepts
Deze opbergdoos voor locomotieven heeft de mogelijkheid om locomotieven rechtstreeks uit de doos te laten rijden.
Tijdens transport zijn de locomotieven beschermd door de stevige doos.
De doos is tevens te gebruiken om onderhoud aan een locomotief te doen.
De locomotief opbergdoos is beschikbaar in 3 lengten: 360, 460 en 560mm.
Meer producten van DCC concepts
Short Crank Pack – 6 cranks and accessories - DCC concepts - working point rodding
€ 21,25
A pack of six low (3.75mm post) brass point rodding cranks plus fixing pins etc.
Locomotive servicing cradle - 240mm - DCC concepts
€ 19,95
Locomotive servicing cradle - 240mm - DCC concepts
Perfect for maintaing your OO / HO/ EM or P4 locomotives.
The locomotive servicing cradle is available in 4 lengths: 240, 340, 440 en 540mm.
More DCC concepts products
Perfect for maintaing your OO / HO/ EM or P4 locomotives.
The locomotive servicing cradle is available in 4 lengths: 240, 340, 440 en 540mm.
More DCC concepts products
Locomotive servicing cradle - 340mm - DCC concepts
€ 21,25
Locomotive servicing cradle - 340mm - DCC concepts
Perfect for maintaing your OO / HO/ EM or P4 locomotives.
The locomotive servicing cradle is available in 4 lengths: 240, 340, 440 en 540mm.
More DCC concepts products
Perfect for maintaing your OO / HO/ EM or P4 locomotives.
The locomotive servicing cradle is available in 4 lengths: 240, 340, 440 en 540mm.
More DCC concepts products
Locomotive servicing cradle - 440mm - DCC concepts
€ 22,45
Locomotive servicing cradle - 440mm - DCC concepts
Perfect for maintaing your OO / HO/ EM or P4 locomotives.
The locomotive servicing cradle is available in 4 lengths: 240, 340, 440 en 540mm.
More DCC concepts products
Perfect for maintaing your OO / HO/ EM or P4 locomotives.
The locomotive servicing cradle is available in 4 lengths: 240, 340, 440 en 540mm.
More DCC concepts products
10 pack Trackbed sheets 3mm - DCC concepts
€ 22,95
10 pack Trackbed sheets 3mm thick.
A box of 10 sheets of high quality trackbed (3mm thick).
Each sheet is 600 x 300 mm.
Made from very long life EVA, closed cell foam trackbed.
The pieces are flat (not on a roll).
Easy to cut with a snap off knife.
More DCC concepts products
6 pack Track Bed sheets 5mm - DCC concepts
€ 22,95
6 pack Trackbed sheets 5mm thick.
A box of 6 sheets of high quality trackbed (5mm thick).
Each sheet is 600 x 300 mm.
Made from very long life EVA, closed cell foam trackbed.
The pieces are flat (not on a roll).
Easy to cut with a snap off knife.
More DCC concepts products