DCC installation accesories

Cobalt α Alpha Power is a well regulated filtered 5 AMP DC power supply which can deliver a super smooth 18v DC at the input terminals of your DCC system, Cobalt α Alpha Central or similar digital device.

It really does not matter which brand of DCC you use – while DCC concepts has “design matched” Cobalt α Alpha Power to their Cobalt α Alpha range, it has also been tested with all of the main DCC systems from “Starter Sets” to full-feature 5 amp systems, and it consistently gives great results with most brands. The only exception is Digitrax Zephyr which requires a lower voltage.

 

These detectors have been designed to be very easy to install. With only a diameter of 4mm, they will fit between the sleepers of Peco Code 100 and Code 75 track.

The detectors are 'Normally Off' and are triggered by a small magnet that is attached to the loco or rolling stock.

Ideal to operate point motors or level crossings
 

6m black decoder wire - DCC concepts

Suitable for DCC installations in N, HO/OO and O.
32 Gauge
0.5 mm thick.


More DCCconcepts products

6m blue decoder wire - DCC concepts

Suitable for DCC installations in N, HO/OO and O.
32 Gauge
0.5 mm thick.


More DCCconcepts products

6m brown decoder wire - DCC concepts

Suitable for DCC installations in N, HO/OO and O.
32 Gauge
0.5 mm thick.


More DCCconcepts products

6m green decoder wire - DCC concepts

Suitable for DCC installations in N, HO/OO and O.
32 Gauge
0.5 mm thick.


More DCCconcepts products

6m grey decoder wire - DCC concepts

Suitable for DCC installations in N, HO/OO and O.
32 Gauge
0.5 mm thick.


More DCCconcepts products

6m orange decoder wire - DCC concepts

Suitable for DCC installations in N, HO/OO and O.
32 Gauge
0.5 mm thick.


More DCCconcepts products

6m pink decoder wire - DCC concepts

Suitable for DCC installations in N, HO/OO and O.
32 Gauge
0.5 mm thick.


More DCCconcepts products

6m purple decoder wire - DCC concepts

Suitable for DCC installations in N, HO/OO and O.
32 Gauge
0.5 mm thick.


More DCCconcepts products

6m white decoder wire - DCC concepts

Suitable for DCC installations in N, HO/OO and O.
32 Gauge
0.5 mm thick.


More DCCconcepts products

6m yellow decoder wire - DCC concepts

Suitable for DCC installations in N, HO/OO and O.
32 Gauge
0.5 mm thick.


More DCCconcepts products

36 pack heat schrink clear - DCC concepts

Length: approx. 55 mm.
Diameter: approx. 2 mm.


More DCCconcepts products

36 pack heat schrink red - DCC concepts

Length: approx. 55 mm.
Diameter: approx. 2 mm.


More DCCconcepts products

Intelligent inductive detector - Legacy Models
The detector works on all layouts powered with every DCC brand or scale and every computer control IO input that can sense a high/low detection.

The detector will detect anything that alters the electrical state in a section. Examples are powered items such as Locomotives, illuminated coaches or rolling stock with resistive wheelsets. Even just a single tail lamp or a lamp in a Guards van or Caboose.

It is simple to install: It needs no soldering or complex set-up. It can be added later or at the time of layout creation. Just create a gap in one rail covering the area you wish to detect and pass the dropper wire which goes from the track power bus to that rail through the hole in the LM-iD coil. No other set-up or fiddling to do. It is that simple.

LM-iD is very easy to connect: every output uses screw terminals and it is possible to easily add an external panel LED and directly connect to and operate both low voltage logic-level things and higher current items such as relays.

One-year warranty.

 

3 pack - Intelligent inductive detector - Legacy Models
The detector works on all layouts powered with every DCC brand or scale and every computer control IO input that can sense a high/low detection.

The detector will detect anything that alters the electrical state in a section. Examples are powered items such as Locomotives, illuminated coaches or rolling stock with resistive wheelsets. Even just a single tail lamp or a lamp in a Guards van or Caboose.

It is simple to install: It needs no soldering or complex set-up. It can be added later or at the time of layout creation. Just create a gap in one rail covering the area you wish to detect and pass the dropper wire which goes from the track power bus to that rail through the hole in the LM-iD coil. No other set-up or fiddling to do. It is that simple.

LM-iD is very easy to connect: every output uses screw terminals and it is possible to easily add an external panel LED and directly connect to and operate both low voltage logic-level things and higher current items such as relays.

One-year warranty.