• info

    You have reached the minimum number

    Shopping cart (0)

    There are no products in your shopping cart yet.

    lights



    Loading...
    3 pack end of train lamps - DCC concepts

    Quick view

    3 pack end of train lamps - DCC concepts

    3 pack end of train lamps - DCC concepts

    € 31,15

    End of Train Lamp (with All Electronics) (3 Pack)

    3x Beautifully crafted scale sized modern EOT lamp complete with 3 full sets of onboard electronics for lamp flash, featuring the ability to automatically turn on/turn off and ready for accessory decoder connection too. Easy mounting with a simple rear pin. Super-fine 0.12mm wire for an almost invisible connection (see online manual for instructions)..
    Manual (pdf)


    More DCCconcepts products

    Working loco lamps LMS/BR - red light - DCC concepts (6 Pack)

    Quick view

    Working loco lamps LMS/BR - red light - DCC concepts (6 Pack)

    Working loco lamps LMS/BR - red light - DCC concepts (6 Pack)

    € 22,95

    Working loco lamps LMS/BR - red light - DCC concepts (6 Pack)

    6 x accurate 4mm scale working loco lamps, LMS / BR type, red light.

    Instructions (pdf)


    More DCCconcepts products

    6 working loco lamps LMS/BR scale O - red light - DCC concepts

    Quick view

    6 working loco lamps LMS/BR scale O - red light - DCC concepts

    6 working loco lamps LMS/BR scale O - red light - DCC concepts

    € 22,95

    6 working loco lamps LMS/BR scale O - red light - DCC concepts

    6 x accurate 4mm scale working loco lamps, LMS/BR type, red light.

    Instructions (pdf)


    More DCCconcepts products

    6 working guards van lamps LMS/BR scale O - white and red light - DCC concepts

    6 working guards van lamps LMS/BR scale O - white and red light - DCC concepts

    € 29,85

    6 working guards van lamps LMS/BR scale O - white and red light - DCC concepts

    6 x accurate 4mm scale working guards van lamps, LMS/BR type, white and red light.
    The lights go on the sides of a guards/brake van with the white light forwards. This is to tell the driver that the guards van is still attached to the, sometimes partly, braked train. A guards/brake van also carries a red light in the center. The three red lights tell signalmen and linesmen that the whole train has passed them.

    Instructions (pdf)


    More DCCconcepts products

    6 working loco lamps LMS/BR scale O - white light - DCC concepts

    6 working loco lamps LMS/BR scale O - white light - DCC concepts

    € 22,95

    6 working loco lamps LMS/BR scale O - white light - DCC concepts

    6 x accurate 4mm scale working loco lamps, LMS/BR type, white light.

    Instructions (pdf)


    More DCCconcepts products

    Gas street/platform lamps - black - 4mm scale - DCC concepts

    Gas street/platform lamps - black - 4mm scale - DCC concepts

    € 37,70

    Gas street/platform lamps - black - 4mm scale - DCC concepts

    Pack Contents
    3x 4mm scale wall lamps with 200mm connection wires
    3x Resistor boards – suitable for connection to regulated DC power 6-12V

    Installation Advice
    Drill the mounting hole using a 2mm drill. Carefully thread the fine wires into the hole, then insert the lamp mounting tube.
    The longer of the 2 wires is the + lead. Connect your power supply to the resistor board and then try the lamp with each of the resistor values to select your preferred light level.
    Alternatively, if a different level is wanted, you may also use any other value 1/4 watt resistor as long as it is larger than 1k Ohms.
    Connect several lamps (up to 6) to one resistor board if you wish.
    Power supply
    Any regulated DC power supply between 6 and 15 volts will be suitable. (To save you any additional cost, you may find one in your bottom drawer, for example an unused mobile phone charger or any similar power supply).

    More DCC concepts products

    Gas Wall lamps - black - 4mm scale - DCC concepts

    Gas Wall lamps - black - 4mm scale - DCC concepts

    € 25,25

    Gas Wall lamps - black - 4mm scale - DCC concepts

    Pack Contents
    2x 4mm scale wall lamps with 200mm connection wires
    2x Resistor boards – suitable for connection to regulated DC power 6-12V

    Installation Advice
    Using a very small drill, drill the building wall to allow insertion of the fine wires. Use glue to fix the lamp to the building.
    The longer of the 2 wires is the + lead. Connect your power supply to the resistor board and then try the lamp with each of the resistor values to select your preferred light level.
    Alternatively, if a different level is wanted, you may also use any other value 1/4 watt resistor as long as it is larger than 1k Ohms.
    Connect several lamps (up to 6) to one resistor board if you wish.
    Power supply
    Any regulated DC power supply between 6 and 15 volts will be suitable. (To save you any additional cost, you may find one in your bottom drawer, for example an unused mobile phone charger or any similar power supply).

    More DCC concepts products

    Swan-Neck street/platform lamps - black - 4mm scale - DCC concepts

    Swan-Neck street/platform lamps - black - 4mm scale - DCC concepts

    € 37,70

    Swan-Neck street/platform lamps - black - 4mm scale - DCC concepts

    Pack Contents
    6x 4mm scale street/platform lamps with 200mm connection wires
    2x 4mm scale wall lamps with 200mm connection wires
    8x Resistor boards – suitable for connection to regulated DC power 6-12V

    Installation Advice
    Drill the mounting hole using a 2mm drill. Carefully thread the fine wires into the hole, then insert the lamp mounting tube.
    The longer of the 2 wires is the + lead. Connect your power supply to the resistor board and then try the lamp with each of the resistor values to select your preferred light level.
    Alternatively, if a different level is wanted, you may also use any other value 1/4 watt resistor as long as it is larger than 1k Ohms.
    Connect several lamps (up to 6) to one resistor board if you wish.
    Power supply
    Any regulated DC power supply between 6 and 15 volts will be suitable. (To save you any additional cost, you may find one in your bottom drawer, for example an unused mobile phone charger or any similar power supply).

    More DCC concepts products

    Swan-Neck Wall lamps - black - 4mm scale - DCC concepts

    Swan-Neck Wall lamps - black - 4mm scale - DCC concepts

    € 25,25

    Swan-Neck Wall lamps - black - 4mm scale - DCC concepts

    Pack Contents
    2x 4mm scale wall lamps with 200mm connection wires
    2x Resistor boards – suitable for connection to regulated DC power 6-12V

    Installation Advice
    Using a very small drill, drill the building wall to allow insertion of the fine wires. Use glue to fix the lamp to the building.
    The longer of the 2 wires is the + lead. Connect your power supply to the resistor board and then try the lamp with each of the resistor values to select your preferred light level.
    Alternatively, if a different level is wanted, you may also use any other value 1/4 watt resistor as long as it is larger than 1k Ohms.
    Connect several lamps (up to 6) to one resistor board if you wish.
    Power supply
    Any regulated DC power supply between 6 and 15 volts will be suitable. (To save you any additional cost, you may find one in your bottom drawer, for example an unused mobile phone charger or any similar power supply).

    More DCC concepts products