There are no products in your shopping cart yet.
DCC concepts
Loading...
6 working loco lamps LMS/BR scale O - white light - DCC concepts
€ 22,95
6 working loco lamps LMS/BR scale O - white light - DCC concepts
6 x accurate 4mm scale working loco lamps, LMS/BR type, white light.
Instructions (pdf)
More DCCconcepts products
Pre-Etched Sleepers 1.6mm (4mm scale) 3 way points - DCC concepts
€ 15,50
4mm scale UK prototype Pointwork sleepering, pre-etched. This fret contains enough correct length sleepers to allow a 3 way point to be constructed. Tie Bars included. Sleepers are 1.6mm thick for direct soldered construction. Designed for 4mm scale / 16,5mm gauge and OO-SF.
template for asymmetric 3 way point (pdf)
More DCCconcepts products
Pre-Etched Sleepers 1.6mm (4mm scale) diamond crossing. - DCC concepts
€ 15,50
4mm scale UK prototype Pointwork sleepering, pre-etched. This fret contains enough correct length sleepers to allow a selection of Diamonds to be constructed. Tie Bars included. Sleepers are 1.6mm thick for direct soldered construction. Designed for 4mm scale / 16,5mm gauge and OO-SF.
The thickness of these sleepers is 1.6mm and they vary in length.
template for 5 and 6 crossing (pdf)
template for 7 and 8 crossing (pdf)
More DCCconcepts products
Pre-Etched Sleepers 1.6mm (4mm scale) double slip - DCC concepts
€ 15,50
4mm scale UK prototype Pointwork sleepering, pre-etched. This fret contains enough correct length sleepers to allow a selection of slips to be constructed. Tie Bars included. Sleepers are 1.6mm thick for direct soldered construction. Designed for 4mm scale / 16,5mm gauge and OO-SF.
template for double slip 7 and 8 (pdf)
More DCCconcepts products
Pre-Etched Sleepers 1.6mm (4mm scale) B9 to A5 Points. - DCC concepts
€ 15,50
4mm scale UK prototype Pointwork sleepering, pre-etched. This fret contains enough correct length sleepers to allow any point between B9 and B6 and A5 to be constructed. Tie Bars included. Sleepers are 1.6mm thick for direct soldered construction. Designed for 4mm scale / 16,5mm gauge and OO-SF.
The thickness of these sleepers is 1.6mm and they vary in length.
template for A5 turnout (pdf)
template for B6 turnout (pdf)
template for B7 turnout (pdf)
template for B8 turnout (pdf)
template for B9 turnout (pdf)
More DCCconcepts products
Pre-Etched Sleepers 1.6mm (4mm scale) single outside slip - DCC concepts
€ 15,50
4mm scale UK prototype Pointwork sleepering, pre-etched. This fret contains enough correct length sleepers to allow a selection of slips to be constructed. Tie Bars included. Sleepers are 1.6mm thick for direct soldered construction. Designed for 4mm scale / 16,5mm gauge and OO-SF.
template for outside slip (pdf)
More DCCconcepts products
ESP wireless DCC Receiver - DCC concepts
€ 64,95
ESP wireless DCC Receiver - DCC concepts
DCC-ESPR.1 is both an ESP® receiver and a 1.5Amp DCC system power bus generator as well as being a very clever “sniffer” device!
DCC-ESPR.1 can be powered by a DCC track bus or with any regulated DC power source or battery able to deliver from 12 to 20 volts.
It has just two pairs of terminals, a power switch and a pairing switch. Connect it to the track bus and it will synchronise mimic panels with all of your accessory operations.
Connect it to the sniffer port of your screen based system and it will update the display.
DCC-ESPR.1 can even be used as the entire basis for an independent DCC power bus, so it really is versatile – and simplicity itself!
DCC-ESPR.1 requires no “programming” and is already provided with a unique address at the time of manufacture. Of course, no two receivers will ever have the same address, so conflicts are 100% impossible!
Unlike Wi-Fi based systems, DCCconcepts ESP® has no limits on the quantity of linked transmitters and there is no need for routers, passwords or computers when using ESP®.
DCC-ESPR.1 has power-off memory and is also protected against wrong connections.
More DCC concepts products
DCC-ESPR.1 is both an ESP® receiver and a 1.5Amp DCC system power bus generator as well as being a very clever “sniffer” device!
DCC-ESPR.1 can be powered by a DCC track bus or with any regulated DC power source or battery able to deliver from 12 to 20 volts.
It has just two pairs of terminals, a power switch and a pairing switch. Connect it to the track bus and it will synchronise mimic panels with all of your accessory operations.
Connect it to the sniffer port of your screen based system and it will update the display.
DCC-ESPR.1 can even be used as the entire basis for an independent DCC power bus, so it really is versatile – and simplicity itself!
DCC-ESPR.1 requires no “programming” and is already provided with a unique address at the time of manufacture. Of course, no two receivers will ever have the same address, so conflicts are 100% impossible!
Unlike Wi-Fi based systems, DCCconcepts ESP® has no limits on the quantity of linked transmitters and there is no need for routers, passwords or computers when using ESP®.
DCC-ESPR.1 has power-off memory and is also protected against wrong connections.
More DCC concepts products
ESP 3-output DCC transmitter - DCC concepts
€ 51,95
ESP 3-output DCC transmitter - DCC concepts
Very easy to use, this unit is the heart of ESP®.
DCC-ESPS.3 can be powered by a DCC track bus or with any regulated DC power source or battery able to deliver from 12 to 20 volts.
DCC-ESPS.3 has three inputs that can be connected to any form of detection or switch and three independent wireless outputs, each with its own DCC address.
The ESP® address range is from 1 to 2044.
To complete your wire-free installation, the DCC-ESPS.3 is paired with the DCC-ESPR.1 receiver which receives the commands and delivers them to your DCC system or control panel, either as a direct DCC command or as a “sniffer” device, so your screen-based DCC system can also receive feedback.
DCC-ESPS.3 can pair with multiple receivers.
Unlike Wi-Fi based systems, ESP® has no limits on the quantity of input channels and there is zero possibility of interference.
ESP® has full power-off memory and is also protected against wrong connections.
More DCC concepts products
Very easy to use, this unit is the heart of ESP®.
DCC-ESPS.3 can be powered by a DCC track bus or with any regulated DC power source or battery able to deliver from 12 to 20 volts.
DCC-ESPS.3 has three inputs that can be connected to any form of detection or switch and three independent wireless outputs, each with its own DCC address.
The ESP® address range is from 1 to 2044.
To complete your wire-free installation, the DCC-ESPS.3 is paired with the DCC-ESPR.1 receiver which receives the commands and delivers them to your DCC system or control panel, either as a direct DCC command or as a “sniffer” device, so your screen-based DCC system can also receive feedback.
DCC-ESPS.3 can pair with multiple receivers.
Unlike Wi-Fi based systems, ESP® has no limits on the quantity of input channels and there is zero possibility of interference.
ESP® has full power-off memory and is also protected against wrong connections.
More DCC concepts products
33m Kapton tape 5mm - DCC concepts
€ 11,45
33m Kapton tape 5mm - DCC concepts
Kapton is extremely thin but also very hard, and makes the perfect insulation tape for installations needing good insulation without bulk.
More DCCconcepts products
Intelligent inductive detector - Legacy Models
€ 23,70
Intelligent inductive detector - Legacy Models
The detector works on all layouts powered with every DCC brand or scale and every computer control IO input that can sense a high/low detection.
The detector will detect anything that alters the electrical state in a section. Examples are powered items such as Locomotives, illuminated coaches or rolling stock with resistive wheelsets. Even just a single tail lamp or a lamp in a Guards van or Caboose.
It is simple to install: It needs no soldering or complex set-up. It can be added later or at the time of layout creation. Just create a gap in one rail covering the area you wish to detect and pass the dropper wire which goes from the track power bus to that rail through the hole in the LM-iD coil. No other set-up or fiddling to do. It is that simple.
LM-iD is very easy to connect: every output uses screw terminals and it is possible to easily add an external panel LED and directly connect to and operate both low voltage logic-level things and higher current items such as relays.
One-year warranty.
More DCC concepts products
3 pack - Intelligent inductive detector - Legacy Models
€ 68,60
3 pack - Intelligent inductive detector - Legacy Models
The detector works on all layouts powered with every DCC brand or scale and every computer control IO input that can sense a high/low detection.
The detector will detect anything that alters the electrical state in a section. Examples are powered items such as Locomotives, illuminated coaches or rolling stock with resistive wheelsets. Even just a single tail lamp or a lamp in a Guards van or Caboose.
It is simple to install: It needs no soldering or complex set-up. It can be added later or at the time of layout creation. Just create a gap in one rail covering the area you wish to detect and pass the dropper wire which goes from the track power bus to that rail through the hole in the LM-iD coil. No other set-up or fiddling to do. It is that simple.
LM-iD is very easy to connect: every output uses screw terminals and it is possible to easily add an external panel LED and directly connect to and operate both low voltage logic-level things and higher current items such as relays.
One-year warranty.
More DCC concepts products
4 baseboard alignment dowels with powerpoint- DCC concepts
€ 24,95
4 baseboard alignment dowels with powerpoint- DCC concepts
These dowels are fitted with power bus conntion.
2 pairs of precision baseboard alignment dowels. Easy to install for accurate joining of baseboards.
Tools needed are: a pilot drill and a 13mm and 19mm spade bit.
2 pairs is enough to make two joints (Joins three baseboards together).
More DCCconcepts products